Century Hawk Pro Bedienerhandbuch

Hawk ProInstruction ManualSPECIFICATIONS Main Rotor Diameter 49.5 in. Tail Rotor Diameter 9.3 in. Overall Length 46 in.

Section 13: Rotor head linkageBefore any pushrod adjustments are made center both sticks and servos on the transmitter. Section 12: Cyclic servo linka

Section 17: Mounting the canopy17.117.217.317.4Carefully cut out the windshield area from the canopy (17.1) with a sharp hobby knife. Trial fit the can

Main Sub-AssembliesThis section will overview parts that came pre assembled from the factory. Items not attached to main sub assemblies can be found i

13Upper Side Frame ExteriorUpper side frame set#HI3107Washout arm set#HI3152C(comes assembled uses #CNBB0730 Ball bearing)Swashplate set#HI3146BAiler

M3x30 socket head cap screw (2)M3x5 flat washerM3x5 flat washerAileron bellcrank set #HI3031BElevator lever set #HI3032BM3x7 ball bearing (4) #CNBB0730(

Main gearAutorotation bearing set#HW3050 (inside main gear)Autorotation bearing set#HW3050 (inside main gear)Main gear#HI3056Starter shaftM5x10 collar

Tail Section InteriorServo side frame set #HW3115AFront canopy mount set #HI3129Servo Side Frame SetFuel tank set#HI3138ALower side frame set#HW3112CE

Torque tube male end (also includes collar from page 16) #HI3065Torque tube shaft set #HW3063TSTorque tube shaft only #HW3063STorque tube bearing case

CN2208B Metal Swashplate Anti-rotation Bracket - blackCN2208P Metal Swashplate Anti-rotation Bracket - purple CN2213 2oz Header Tank w/ Machined M

Hawk Pro Replacement Parts HW3000 CN0402 CN2226 HI3007 HI3009 HI3010 HW3011 HW3017 HI3020A HW3024 HI3031A HI3032B HI3035A HI3040 HW3042

2IntroductionCongratulations on your purchase of Century Helicopter Product’s latest version of our HAWK series RC helicopter model. The Hawk Pro hel

HI3099 HI3102A HI3106A HI3107 HI3112C HW3115A HI3122 HW3123 HW3127A HI3129 HI3146B HI3152C HI3152A HI3160B HW3161A HI3167A HI3167B

Carbon Fiber Tail BoomGet that attractive woven Carbon Fiber look with these light carbon fiber tail booms CN2126H Carbon tail boomCNC Machined Alumin

Head Button(Hawk, Falcon & Phoenix)Left hand threaded Black or Purple anodized head button for easy stopping of the rotor head.CN2215B BlackCN22

Hobby scissorsHardware Description and Identification: M3x6 = 3x6mm and can refer to screws or ball bearings.M3x6 Phillips Machine

Rotor head itemsTail sectionUpper frame setLower frame set Servo frame setDecal sheetLanding gearWindshieldFin packHardware/ PushrodsClutch, fan &

Section 1: Preparing the engineRemove the thrust washer that comes on the engine from the factory. Only use the 9x14 washer that comes with the fan an

Section 3: Installing servos to servo trayInsert and attach the lower throttle servo on the left side (3.1) with the output “horn” fac-ing the front o

Section 5: Muffler & fuel routing5.25.35.4Section 6: Flybar & head assembly6.15.1Install the pressure nipple using a high temperature adhesive

Remove the 3 socket head cap screws to open the gearbox in order to grease the gears.8.1Section 7: Landing gear7.17.27.3All components for installing

Section 10: Tail control rod & pitch controlUse the radio to center the rudder servo. Mount the servo arm/horn perpendicular to the tail pitch con